|#0100 Perfec Clean Mats & Grates|
Our Perfec Clean Mats & Grates provide a comfortable, surefooted surface that helps eliminate wet, slippery floors caused by tracked in mud, dirt, and water. These mats are available in either our exclusive thermoplastic rubber hinge or our standard aluminum hinge. Mats can be recessed or surface mounted. Our grates are manufactured of rigid aluminum rails that allow dirt, sand, and water to collect below the surface. All our floor products are available in a wide range of colors and materials to accent your building design.
|#0102 Pyramid Rubber Mats|
This unique surface has a continuous pyramid design for safer foot traction. These mats offer maximum abrasion resistance and are ideal where wheeled carts and equipment are used. Knob underside offers maximum aeration and water drainage. Custom inlaid logos also available.
|#0105 Vinyl Link Mats|
Superb shoe cleaning properties that reduce building maintenance.
Mat first removes dirt, then contains it deep within corrugations.
Note: Not recommended where heavy equipment will be rolled over mats or for recessed areas greater than 8' wide, unless mat is to be sectionalized.
|#0108 Mat Recess Frame|
Made of extruded 6063 aluminum alloy and are fabricated to exact dimensions to insure fit to the mat. Frames are supplied with mitered corners and shipped unassembled with all necessary anchor keys and corner pins. Frames must be assembled at the job site and installed so that upper edge is level with finished floor surface. The frame should be anchored into cement with anchor keys a minimum of 24" on centers. Corner pins should be installed at all corners of frame. For use on mats of 3/8" - 5/8" thickness.
|#0110 Velva Tiles|
This is a unique floor covering in tile and strip form manufactured from recycled strips of industrial tire carcasses. The walking surface of the strips is chenille and vulcanized to a flexible backing. It is tough, non-absorbing, high wear flooring for use indoor or outdoor, in public
buildings, schools, ramps, locker rooms, or entrances. May be vacuumed. Use mild detergent and stiff brush to clean heavily soiled areas. Use our environmentally friendly adhesive to bond tiles to floor.
Adhesive covers approximately 150 square feet per gallon.
|#0111 Water Hog Classic Square & Geometric Tiles|
Special non-thermoplastic Tri-Grip™ rubber backing insures dimensional stability. Available in 1/4" or 7/16" thickness. Two patterns available: Square and Geometric. Damaged or worn tiles can be replaced easily.
|#0112 Water Hog Premier Diagonal & Diamond Tiles|
Unique ridged rubber reinforced design traps dirt and wicks moisture beneath the shoe level so that it is not tracked into your facility.
Exclusive rubber-reinforced face nubs extend the performance life by maintaining the bi-level construction in the pattern. The anti-static 100% premium polypropylene fiber system will dry quickly, and will not fade or rot. Available in thicknesses of 1/4" or 7/16". Two patterns available: diagonal and diamond. Damaged or worn tiles can be replaced easily.
|#0117 Tile Lock Rubber Gym Tiles|
High shock absorbency and long wearing toughness make tile lock rubber gym tiles the popular choice for all types of athletic facilities.
Etched surface pattern provides sure footing. Protects floor from skate blades and free weights. Outside dimension of areas to be covered must be divisible by 2" when using standard sections. Tiles can be custom cut on site.
|#0201 Corrugated Rubber Matting|
Runner matting for heavy traffic areas, where non-slip, high traction features are required. Quiets noise, saves floors in wet or dry weather. Most widely used where floor protection and safety are vitally important. Easy to clean, won't curl. This matting can be handled more easily under cold conditions than can vinyl.
|#0202 Smooth Vinyl Matting|
This vinyl matting is smooth on both sides. Great for protecting counter tops, work benches and tool boxes. This material is oil and water resistant and is not affected by most corrosive chemicals.
|#0203 Wide Rib Vinyl Matting|
Vinyl runner matting is tough. It gives exceptionally long service. Highly resistant to grease, oils and chemicals, while not becoming brittle with age. (Note: not resistant to solvents and gasoline.) It is easy to keep clean with its wide rib surface pattern. For heavy duty matting, see item #0208B.
|#0203A Corrugated Vinyl Matting|
Same popular design as our standard corrugated rubber matting, but at a very economical price. Quiets noise, saves floors in wet or dry weather. Most widely used where floor protection and safety are vitally important. Easy to clean.
|#0203B Pyramid Vinyl Matting|
Non-directional pyramid pattern combined with a special formulation resulting in an exceptionally slip-resistant mat. Resists many oils, greases and fats. Ideal for ramps, airports, walkways, factories, restaurants, office buildings and department stores.
|#0205 Diamond Plate Vinyl Matting|
Diamond plate is a uniquely engineered, deeply- embossed, steel design matting. It is recommended for heavy traffic areas where floor protection and safety are important. It exhibits exceptional wear characteristics and is ideal for heavy traffic. Also has good resistance to most beverages, normal oils, usual household cleaners and common industrial chemicals.
|#0205Y Safety Striped Diamond Plate Vinyl Matting|
Same design as our standard diamond plate matting, (#0205), but with the added feature of a highly visible 4-1/2" wide yellow border on both sides.
|#0206 Tuff-Trac Vinyl Matting|
Attractive modern herringbone ribbed surface design. Helps to provide added traction for employees and public during slippery or wet conditions. The ribbed surface design removes particles and moisture from shoes. Meets flammability test requirements of MOTOR VEHICLE SAFETY STANDARD NO. 302.
|#0207 Clear Vinyl Matting|
Clear runner matting with tiny "grippers" on the reverse side holds it securely in place, yet won't damage your carpet. It is transparent to let carpet beauty show through. Handsome surface pattern makes it easy to clean. Tapered borders along both edges lay flat to reduce tripping hazards to a minimum.
|#0208A Heavy Duty Corrugated Vinyl Matting|
This double thick matting combines toughness for long wear in heavy traffic areas. Resistant to oils, greases, and chemicals. Sharp, v-rib corrugations run lengthwise on this matting and are designed to help remove dirt and protect floors.
|#0208B Heavy Duty Wide Rib Vinyl Matting|
Same durable vinyl material as our 1/8" (#0203) material, but at twice the thickness. This material features a round ribbed corrugation running the length of the mat. When you need extra protection and long life, this mat is the one. Easy to clean and has good resistance to many acids and chemicals.
|#0209 Spike Resistant Wide Rib Vinyl Matting|
Wide ribbed surface permits easy cleaning. Matting is exceptionally tough and will give years of service. Resists golf-shoe spikes. Especially recommended for areas of rough usage in industrial plants. Not affected by oily or greasy conditions.
|#0211B Knob Top Niru Rubber Matting|
The tough knobbed bar design of this matting adds safety and traction in all wet and dry applications. The rubber is compounded of 100% nitrile for grease resistance. This matting is ideal for food processing plants, kitchens, hospitals, laboratories and industrial plants.
|#0211CHD Versa Runner Rubber Matting|
This thick, heavy duty mat has done excellent work in kitchens, food processing plants, locker/shower rooms, around swimming pools and behind bars. It is compounded to resist grease, oil, acids, and alkalies. Slotted holes provide good drainage. This matting gives greater foot-ease and stability.
|#0211D Deep Freeze Safety Matting|
Specifically formulated to perform in deep freezer applications. Tested to withstand to minus 40 degrees fahrenheit. Raised knob solid surface to enhance traction.
|#0213 Corrugated Rubber Switchboard Matting|
Conforms to ANSI/ASTM D178-93, TYPE 1, CLASS 2. Proof tested at 20,000 volts A.C. Maximum recommended use voltage is 17,000 volts.
Dielectric strength - 30,000 volts A.C. Conforms to OSHA regulations for use near electrical machinery such as fuse boxes, control panels and other heavy electrical equipment.
|#0213D Diamond Plate Vinyl Switchboard Matting|
Conforms to MIL-DTL-15562G (formally MIL-M- 15562F), type III.
This matting uses the functional diamond deck plate pattern for a non slip surface. There are many industrial applications for a matting of this quality.
|#0213M Smooth Marbleized Vinyl Switchboard Matting|
A smooth surface, high voltage insulating vinyl floor covering designed to protect personnel from accidental exposure to electrical potentials not exceeding 3000 volts. Conforms to MIL-DTL-15562G (FORMALLY MIL-M-15562F), TYPE I. Marbelized colors.
|#0213S Smooth Vinyl Switchboard Matting|
A smooth surface, high voltage insulating vinyl floor covering designed to protect personnel from accidental exposure to electrical potentials not exceeding 3000 volts. Conforms to MIL-DTL-15562G (FORMALLY MIL-M-15562F), TYPE II.
|#0213V Corrugated Vinyl Switchboard Matting|
Conforms to ANSI/ASTM D178, TYPE II, CLASS 2. Conforms to TABLE 3 for oil-resistance and flame-resistance. Dielectric strength 30,000 volts A.C. Proof tested at 20,000 volts A.C. Recommended maximum use voltage is 17,000 A.C. Corrugated pattern.
|#0213VD Deck Plate Vinyl Switchboard Matting|
Conforms to ANSI/ASTM D178, TYPE II, CLASS 2. Conforms to TABLE 3 for oil-resistance and flame-resistance. Dielectric strength 30,000 volts A.C. Proof tested at 20,000 volts A.C. Recommended maximum use voltage is 17,000 A.C. Diamond pattern.
|#0214 Kleenrite Rubber Matting|
A lightweight, fine textured, all rubber runner with a non-directional design. Ideally suited for light duty applications. Cleans easily and quickly. Stays put on smooth finished floors.
|#0215 Protect Vinyl Matting|
A cost effective, durable, vinyl runner. Its skid and slip resistant pebble surface is easy to maintain and clean. This material is great for aisles, walkways, stockrooms and assembly lines.
|#0220 Nyracord Counter Tread Matting - Grease Resistant|
Grease resistant counter tread is blended from Nyracord rubber and nitrile to provide the most durable oil resistant anti-slip matting on the market. Open slot design allows oils or solvents to flow through the mat providing a safe slip-resistant working surface. All this with the benefit of anti-fatigue properties. Also available in a non grease resistant version (#0221).
|#0221 Nyracord Counter Tread Matting - General Purpose|
Made of rubber compound and nylon fibers that stands up to years of tough use. Even forklift traffic is no match. The open slot design promotes safety, allowing particles, moisture and solvents to drop through the mat. The knobby underside creates a cushion of air, providing maximum worker comfort. Rounded edges will not curl. Also Available in a Grease Resistant Version (#0220).
|#0222 Nyracord Perma Walk Matting|
Great protection for high traffic areas. Easy to clean with rib running full length of mat. Excellent for areas where forklifts or wheeled carts are used. Ribbed underside for aeration, preventing mildew. Ideal for golf courses, hockey rinks, weight rooms, warehouse aisles, horse trailers.
|#0225HT 3M Nomad High Traffic Matting|
#8150 - Backed
#8100 - Unbacked
The perfect dirt stopper for outside and recessed applications. This durable mat stands up to heavy traffic and scrapes dirt and grime off shoes. The unbacked version allows dirt and moisture to drain through for easy cleanup.
|#0225NCP 3M Nomad Cushion Plus Medium Traffic Matting #6050|
Nomad material collects dirt and keeps it hidden beneath an attractive top surface of unique resilient loops of 100% vinyl. Vinyl foam backing helps keep the mat in place. Tracking of dirt and moisture is minimized, protecting your clean floors and carpets. Easy and inexpensive to maintain. Just shake, vacuum or rinse out.
|#0225UBN 3M Nomad Unbacked Medium Traffic Matting #1500|
Same high quality material as our nomad cushion plus except without a backing. The open construction allows water to run through the matting.
The matting stays dry and helps to reduce the possibility of slips and falls. Made for locker rooms, for use around showers, saunas and whirlpools.
|#0227 Lounge Matting|
This material is ideal for any type of entrance area, indoors and out.
Lounge is impervious to ultra- violet light and can be cut into any size or shape without danger of the edges unraveling. Lounge is tough as steel, but looks like carpet. Can be direct glued down or made into custom size mats with edging applied to all sides.
|#0228 Super Berber Matting|
Like all of our polypropylene matting, Super Berber matting is long wearing and UV stable. It can be used indoor or out. Super Berber can be vacuumed, steam cleaned or hosed off. It can be cut at any angle without danger of the edge unraveling. Available with a smooth backing for recessed application or knob back for free lay application. Custom sizes are available with a high profile vinyl edging applied to all sides.
|#0229 Sole Survivor Matting|
Sole Survivor is the longest wearing walk-off matting available and is UV stable. It can be used indoor or out. Sole survivor can be vacuumed, steam cleaned or hosed off. Can be cut at any angle without danger of the edge unraveling. Available with a smooth backing for recessed application or knob back for free lay application. Custom sizes are available with a high profile vinyl edging applied to all sides. Custom inlaid logo's are also available for that personal touch.
|#0302 Rely-On Olefin Matting|
Hard wearing 100% continuous filament Olefin pile takes heavy traffic without fuzzing or pilling. Colorfast, even in direct sunlight. Traps one gallon of water per square yard. Easy to clean - just vacuum or hose.
Backed with solid vinyl for even greater protection.
|#0303 Wonder-Pro Olefin Matting|
This mat features 17 ounces of 3300 denier, continuous filament Olefin yarn per square yard. Absorbs moisture and dries quickly. 100% Olefin solution-dyed yarns maintain eye catching and attractive color
appearance. 16 different shades that coordinate with any interior design. This heavy-duty Olefin mat provides greater wiper service than other customary Olefin mats. A 65 mil, durable, solid vinyl backing reduces mat movement.
|#0304 Grounds-Keeper Olefin Matting|
Hard wearing 100% continuous filament Olefin pile takes heavy traffic without fuzzing or pilling. Colorfast, even in direct sunlight. Traps one gallon of water per square yard. Easy to clean - just vacuum or hose.
Backed with solid vinyl for even greater protection. Three year warranty!
|#0305 Rug-Hugger II Olefin Matting|
Foam backing is fused to mat to help it stay in place, when placed on top of carpet. 100 percent continuous filament Olefin pile carpet.
Solution dyed to resist fading. Traps over one gallon of water per square yard. Deep pile attracts dirt and grime.
|#0309 Stat-Zap Matting|
Two-ply, continuous filament nylon with conductive fibers to drain static electricity away in milliseconds. No grounding cord is required.
Resistivity is 109 ohms. Standard size mats include grounding cord. On custom mats, grounding cord must be ordered separately.
|#0310 Fore-Runner Matting|
This premium outdoor scraper mat removes heavy dirt and debris from shoe bottoms before it reaches your front door. This mat features 19 ounces per square yard of ribbon polypropylene which provides vigorous scraping action, removing dirt from shoe bottoms and holding it beneath the surface of the mat. The durable, loop-twist construction performs under the harshest of conditions. Our vibrant colors retain luster even after years of heavy use. An 80 mil durable, solid vinyl backing reduces mat movement. Overall thickness, 5/16".
|#0311 Cross-Over Matting|
This transitional, wiper/scraper mat removes dirt, grit and moisture before it enters your facility. This mat features 19 ounces per square yard of continuous filament, loop pile olefin combined with polypropylene ribbon yarn in a loop pile construction, to remove dirt and moisture from shoe bottoms, holding it beneath the surface of the mat.
Crush-resistant, even under high traffic conditions. Our vibrant colors retain luster even after years of heavy use. An 80 mil durable, solid vinyl backing reduces mat movement. Overall thickness, 5/16".
|#0312 Walk-A-Way Matting|
This premium Olefin wiper mat acts as the final line of defense against dirt and moisture being brought into your facility. Mat features 19 ounces per square yard of continuous filament, loop pile, olefin yarn in a loop pile construction. This mat is crush-resistant, even under high traffic conditions. Vibrant colors retain luster even after years of heavy use. An 80 mil durable, solid vinyl backing reduces mat movement.
Overall thickness, 5/16".
|#0313 3M Entrap All Season Mats|
Provides excellent scraping action for superior dirt and water removal.
The foam backing reduces creeping and holds the moisture and dirt off the floor. Mat construction provides a channel between layers to improve drainage.
|#0315 Water Hog Mats|
A unique ridged construction which effectively removes and traps dirt and water before it enters your building. Made of 100% polypropylene fiber that won't fade, rot and dries quickly. Our special cleated rubber backing keeps mat in place, prevents creeping on most carpets and provides excellent grip on hard surfaces. Also available in Water Hog Fashion Design (see #0315F)
|#0315F Water Hog Fashion Mats|
Same design as Water Hog mat but with a fabric border. Unique ridged construction which effectively removes and traps dirt and water before it enters your building. Made of 100% polypropylene fiber that won't fade, rot and dries quickly. Our special cleated rubber backing keeps mat in place, prevents creeping on most carpets and provides excellent grip on hard surfaces.
|#0317 Two-N-One Matting|
A great looking wiper mat with the superior cleaning qualities of a scraper mat. This mat is especially tufted of Olefin and polypropylene yarn that is stain resistant. It provides long service under the most demanding conditions and is easily maintained with a vacuum or extractor.
|#0318 Chevron Matting|
The decorative chevron pattern promotes multi-directional brushing action. The 100% polypropylene needle punch fibers help retain moisture and channel dirt away. Bonded to a durable pvc backing.
|#0319 Needle Pin Matting|
Non-directional, high-low pattern promotes aggressive shoe cleaning action and resists matting down. Solution dyed polypropylene fiber resists staining and color fading for extended service. The mat is easily cleaned with a vacuum or hose. The heavy duty vinyl backing keeps the mat flat and in place.
|#0320 Needle Rib Matting|
The unique ribbed design traps and hides dirt, yet is easily cleaned.
The deep ribbed needle punch is made from 100% polypropylene, which offers exceptional long wear and color fastness. The heavy gauge vinyl backing protects the floor from abrasion and moisture.
|#0340 Tri-Grip Nylon Mats|
These mats are made from a heavy 100% nylon face yarn that offers outstanding absorption and durability. The heatset twist yarn resists packing and crushing. The dirt filters into the mat face instead of remaining on top. Our special cleated rubber backing keeps the mat in place and resists creeping on most carpets.
|#0341 Water Hog Premier Mats|
Ridged construction effectively removes and traps dirt and moisture below shoe level. Exclusive rubber-reinforced face nubs prevent pile from crushing-maintaining high performance and extending product life. Premium Tri-denier polypropylene fiber system. Allows fabric to dry quickly while preventing fading and rotting. 50% heavier than Water Hog Classic. Anti-static rating averaging 1.2kv with a maximum average voltage of 1.6kv as measured by the AATCC.
|#0341F Water Hog Premier Fashion Mats|
Same construction as Premier Mat but has a fabric border.
Ridged construction effectively removes and traps dirt and moisture below shoe level. Exclusive rubber-reinforced face nubs prevent pile from crushing-maintaining high performance and extending product life. Premium tri-denier polypropylene fiber system. Allows fabric to dry quickly while preventing fading and rotting. 50% heavier than water hog classic. Anti-static rating averaging 1.2kv with a maximum average voltage of 1.6kv as measured by the AATCC.
|#0342 Water Hog Diamond Cord Mats|
Exclusive rubber-reinforced face nubs prevent pile from crushing, ensuring high performance and extended life. Fiber system utilizes a "fiber bundle" made up of monofilament polypropylene and 2750 denier BCF OLEFIN yarn that is air entangled together. This unique construction produces exceptional wiping and scraping performance.
Anti-static rating averaging -0.1kv with a maximum average voltage of 0.2kv as measured by the AATCC. The "water-dam" traps dirt and water so they stay on your mat and off your floors, minimizing slip hazards and floor damage.
|#0343 Color Star Mats|
Mats are manufactured from state of the art solution dyed nylon fibers.
Yarn is twisted and heat set to enhance dirt and moisture collection.
Cleated rubber backing keeps mat in its place.
|#0344 Grand Premier Mats|
Unique ridged construction effectively removes and traps dirt and moisture beneath shoe level. Exclusive rubber-reinforced face nubs prevent pile from crushing— maintaining high performance and extending product life. Premium polypropylenee fiber system allows fabric to dry quickly and prevents fading and rottings. Mats can easily be vacuumed or hosed off. Grand Premier's highly durable attractive fashion border makes it the perfect choice for indoor or outdoor applications. Available in flat or gripper type backing. Exclusive "water dam" allows Grand Premier to trap dirt and water so they stay in the mat and off your floor-minimizing slip hazards and floor damage around the perimeter of the mat. Anti-static rating averagin 1.2kv with a maximum average voltage of 1.6kv as measured by teh AATCC. A wide selection of 31 standard commercial sizes makes finding the right mats for your needs quick and easy.
|#0403 Tire Link Mats|
Tough mats made from rubberized fabric links woven on heavy galvanized spring steel wire. The links are 5/8" thick x 2 1/2" long woven on wires in v-shape herringbone construction. These mats can be used at doorways, behind counters, in front of work benches, on assembly lines, and in machine shops.
|#0407A Vinyl Backed Cocoa Matting|
Here is the first shoe and boot cleaning fiber known to man. 3/16" thick vinyl backing completely protects floors with no leak-through as with woven brush mats. These mats are easily cleaned by shaking, vacuuming or rinsing. Also available in rolls and are ideal for vestibules and recessed applications. Maximum size available is 78-3/4" wide x 41' long.
|#0407B Woven Backed Cocoa Mats|
For thorough shoe cleaning, nothing can match a cocoa mat.
This heavy duty mat has a " one way" absorbing action that holds up to 2 gallons of water per square yard. It won't release moisture when walked on. Easily cleaned by turning it upside down and sharply rapping with a broom handle.
|#0408 Mat-A-Dor Mats|
Just step on this mat and it cleans your shoes automatically. Hundreds of resilient rubber fingers go to work the moment they are stepped on.
Borders are beveled to prevent tripping. Mat hides trapped dirt, and keeps dirt out of your building. Excellent for anti-fatigue in stand-up jobs.
|#0409 Flexible Steel Link Mats|
The original, continuous, crimp, flexible mat, made from galvanized steel 3/8" deep with 1" x 1" mesh openings. It rolls up like carpet for easy cleaning. This mat presents a smooth level surface for truly rough and tough scraping jobs. This mat is also great for those areas where mud and dirt are a real problem.
|#0415 Safety Scrape Rubber Mats|
Heavy durable Safety Scrape mats work wonders in environments where traction is essential. In kitchens, locker rooms, on inclines, behind lunch counters and bars, in production areas and outside entrances . Constructed of 100% nitrile rubber for oil and chemical resistance. Molded face cleats act as scrapers to remove heavy dirt and soil from shoes and provide an excellent anti-skid surface. MOLDED Anti-skid gripper backing. Available in four OSHA approved striped color border.
|#0417 Super Scrape Rubber Mats|
Effectively scrapes tough dirt and grime off feet. Super-Scrape mats are reversible and, when placed with the non-scraper side up, can even be used as anti-fatigue mats. Durable nitrile-rubber mat provides slip-resistant surface. Available with safety messages, a welcome message or custom logos. 100% nitrile rubber Super Scrape is ideal for kitchens, locker rooms, slippery inclines, restaurants, production areas and outside entrances. Super Scrape logos are available in red, green, yellow, orange, gold, white and blue. One color per logo. Super Scrape with messages are available in red only.
|#0420 Comfort Flow Anti-Fatigue Rubber Mats|
Constructed of 100% high density closed cell nitrile rubber. Far superior in grease and oil resistance than other "grease proof" mats. Excellent anti-fatigue properties for added employee comfort. Low profile and slip-resistant surface reduces slip and fall accidents. Non-skid backing keeps mat in place.
Anti-microbial Treated - guards against degradation from micro-organisms and minimizes mats being a source of odors.
|#0421 Hog Heaven Anti-Fatigue Mats|
Solid Nitrile Rubber surface for better chemical resistance. Textured Nitrile Rubber surface for superior slip resistance. Closed - cell Nitrile/PVC cushion backing provides long-lasting comfort without breaking down. 100% Nitrile Rubber border remains flexible for the life of the product and will not crack or curl. Hog Heaven is available in two thicknesses:5/8" and 7/8". Available in black and OSHA - approved striped border colors: yellow, red, green, and orange.
|#0430 Comfort Scrape Anti-Fatigue Rubber Mats|
Lightweight, easy to clean material outperforms thicker, heavier mats.
Low profile design slip resistant surface helps minimize slip and fall accidents. Anti-static, nitrile rubber compound is ideal for use in packaging and assembly areas, industrial workstations, machine shops and welding stations. 100% high density, closed cell nitrile rubber cushion provides maximum resistance to waters, oils, greases, chemicals and animal fat.
|#0450 Safeguard Slip Prevention Products|
Patented SAFEGUARD® Hi-Traction and High glow Traction Covers provide the anti-slip protection you need every time. The proven SAFEGUARD® surface is factory applied to a selection of base materials, depending on your needs. These include stainless steel, galvanized steel, pultruded FRP/GRP composite (fiberglass) and vinyl (flexible PVC) sheeting.
|#0500 Renovation Stair Treads|
Our renovation treads are manufactured of high quality, heavy duty extruded aluminum with our exclusive safety traction surface.
Treads install easily over existing worn stairways of concrete, wood, steel or terrazzo. Available with optional sightline or glow in the dark front edge. Holes are drilled and countersunk.
|#0501-375 Medium Duty Vinyl Stair Treads|
This tread was designed for use in apartment projects and light commercial applications. Lower initial cost, ease of installation, ease of cleaning and long service appeals to apartment owners and builders.
|#0501-400 Heavy Duty Vinyl Stair Treads|
Use the heavy gauge sharp-rib design koroseal vinyl tread for your heaviest traffic. 1/4" thick wear area, easily trimmed to cover and fit any stair step. Install over concrete, metal, wood terrazzo. Extra heavy thickness at the front "wear area". Meets federal specs. RR-T-650E
|#0501-622 Diamond Design Rubber Stair Treads|
The original diamond design extends the full width of the tread to a 6" depth. This tread is ideal for commercial or industrial applications.
Treads should be installed with a neoprene contact cement.
|#0503 3M General Purpose Safety Walk|
This material fits your specific needs, in assorted shapes and sizes.
Assists in preventing costly slip and fall accidents and helps in complying with strict osha safety standards. This material can be used indoors or out, wet or dry, even around oil and grease. It goes on like tape to a clean, dry surface and is ready for immediate service.
|#0503-CONF 3M Conformable Safety Walk|
Mineral coated anti-slip material with aluminum backing that conforms around corners and to irregular surfaces. Used on diamond tread safety plates, steps, ladders, ramps, equipment, vehicles and other irregular surfaces.
|#0503A 3M Safety Walk Primer|
For use in priming and sealing porous surfaces prior to application of safety walk anti-slip surfacing.
|#0503B 3M Safety Walk Edge Sealer|
For sealing edges of safety walk that are exposed to excessive water, grease or oil.
|#0504 3M Resilient Safety Walk|
Medium, textured, polymer material for use on smooth flat surfaces.
Used in wet, barefoot traffic areas such as showers and locker rooms.
|#0506 Acrylic Desk Chair Mats|
Crystal clear mats that let the beauty of your fine carpeting or flooring be seen, but protected from dirt and marring. These mats are constructed of an acrylic sheet with smooth rounded edges.
|#0506AR Vinyl Anchor Desk Chair Mats|
Our anchor mat sits still, even if you don't. Our mat has hundreds of rigid anchors that hold the mat in place. The textured surface facilitates easy but controlled movement of caster chairs. The vinyl material is scuff-resistant and is transparent to let the beauty of your carpet show through.
|#0506L3 Textured Co-Polymer Desk Chair Mats|
This mat can take it all. If you have trouble with acrylic mats cracking, or vinyl mats bending, then this is the mat for you. It is made of a special co-polymer compound, which just won't break. Available with anchor backing.
|#0512 Anti-Vibration Pads|
When properly sized and installed under machines, these solid neoprene pads prolong machine life, reduce maintenance costs, dampen vibration, and isolate noise telegraphed through the floor. Pads are engineered for a maximum load capacity of 50 psi.
|#0601 Air Flex Anti-Fatigue Mats - Fabric Top|
AirFlex's comfortable, functional dome design provides excellent relief from back and leg stress. Launderable and highly chemical-resistant nitrile rubber backing provides excellent cushion during use, maximum durability and longer life service. AirFlex's solution-dyed polypropylene surface means exceptional stain-resistance and ease-of-maintenance.
To clean, simply sweep, vacuum or hose-off as needed. Perfect for retail or commercial applications and available for work in wet or dry environments. Rounded corners and fashionable colors add the finishing touches to this attractive, high-performance anti-fatigue mat.
|#0601R Air Flex Anti-Fatigue Mats - Rubber Top|
All nitrile rubber design. Comfortable, functional dome design provides excellent relief from back and leg stress. Highly chemical-resistant nitrile rubber provides excellent cushion during use, maximum durability and longer life service. To clean, simply sweep, vacuum or hose-off as needed. Perfect for retail or commercial applications and available for work in wet or dry environments. Rounded corners.
|#0602A Interlocking Anti-Fatigue Mats|
Our interlocking mats feature a dimpled, non-slip tread and non-trip edges. Honeycombed air cells provide suction to floor which prevents slipping of matting. Leg and foot fatigue are practically eliminated. Boosts employee efficiency when standing long hours is required.
Single, end and center mats are available in greaseproof neoprene or non-greaseproof standard rubber. Center sections can be added later to increase length of mat.
|#0603 Comfort King Anti-Static Anti-Fatigue Matting|
Our new material is made of static dissipative, anti-fatigue sponge vinyl.
The surface resistivity tests at 10-9 ohms per square foot. The pebble surface provides safe foot traction and yet is easy to clean. This is the mat for electronic assembly, test benches, test stations, or checkout counters.
Grounding cord is required for each mat.
|#0604 Tuff-Spun Anti-Fatigue Matting|
A must for worker comfort and safety. This mat is available in two different thickness of durable sponge vinyl, 3/8" Tuff-Spun and 5/8" Super Sponge. This anti-fatigue material increases productivity throughout the workplace.
|#0604S Safety Striped Tuff-Spun Anti-Fatigue Matting|
This material not only promotes comfort, it also promotes safety. The highly visible yellow safety border channels foot traffic along the path of the runner. This mat will surely increase employee safety and comfort with its durable surface. Pebble design, ribbed design.
|#0605 Comfort King™ Anti-Fatigue Matting with Zedlan™|
Comfort-King™ offers triple the resiliency of vinyl foam mats. It out performs other anti-fatigue products in low temperatures. It's extended durability keeps it performing twice as long as typical pebble mats and 3 times longer than ribbed surface products. Comfort-King™ with Zedlan™ reduces strain on feet, ankles, legs and lower back. This mat induces natural flexing of the muscles, reducing the build-up of lactic acid that causes fatigue.
|#0605S Safety-Striped Comfort King Anti-Fatigue w/Zedlan|
All anti-fatigue mats can improve productivity and slash workers' compensation claims. Comfort-King does it better than almost any other mat available anywhere. Now with bright yellow borders that increase worker awareness and safety. In your choice of two popular Comfort-King weights. Made with our patented Zedlan foam with 3 times the resilience of ordinary vinyl foam mats.
|#0606 Electrically Conductive Deck Plate Anti-Fatigue|
This resilient anti-fatigue mat reduces employee fatigue while helping to protect sensitive electronic equipment from uncontrolled electrical surges and spark activity. This mat helps prevents accumulation of static. Diamond plate top surface is cast to a foam base promoting enhanced traction for lasting comfort and safety. Excellent surface resistivity Surface to surface 105 ohms Surface to ground 105 ohms
1 grounding cord should be installed for every 10 feet of matting.
STANDARD MATS INCLUDE GROUNDING CORD, ROLLS DO NOT.
|#0607X Double Thick Super Foot Lover Mats|
Extra thick, a full 1 1/4" thick mat made for industrial work or process stations. Makes operating foot activated controls easier because the operator is upon a cushioned platform.
|#0611 Multi-Mat II Rubber Matting|
No other mat offers all these features. Mat is not only reversible, but it is highly resistant to grease, oils and fats. Multi-Mat has excellent cushioned support, and is easy to clean. Raised knobs facilitate drainage. Dirt and grease flush away easily. Non-skid in even wet greasy conditions. Lightweight for ease of handling.
|#0611A Traction Matting|
Same high quality material and workmanship as our Multi-Mat II(#0621), except without the holes.
|#0613 Dri-Dek Interlocking Tiles|
12" x 12" interlocking modular tiles for those areas where safety and comfort are critical. Open design allows water and debris to fall through the tile and out the drain. Tiles snap quickly together and can be easily trimmed to fit wall to wall applications. Perfect for showers, saunas, locker rooms or any work station.
|#0614 Floorline Vinyl Matting|
This is a functional matting constructed of heavy wall flexible pvc tubes, electronically welded together in a grid form. This mat should be used in showers, saunas, pools or locker rooms, where a non-skid surface is needed. It will cushion your feet and will not slip even on a wet floor.
|#0614A Heron Rib Duckboard Vinyl Matting|
Resilient cushion construction eases worker fatigue and reduces breakage of dropped parts or equipment. In addition to their anti-slip, waterproof and abrasion resistant qualities, these mats are impervious to oils, grease, acids and alkalis.
|#0614HA Heron Aire Lite Vinyl Matting|
Superior slip resistance, anti-fatigue properties and lower cost makes this the mat of choice where duckboard is not necessary. The hollow ribs provide comfort underfoot.
|#0616 Cushion Tiles - Solid|
Cushion tile is the functional solution to the elimination of fatigue, vibration and slipping. The mat is made of durable vinyl plastic and is easy to install and custom cut to fit. Ramped edges are available with the same interlocking mechanism. Resistant to most chemicals. Can be used in industrial plants, machine shops, exercise rooms, health clubs, swimming pools, hot tubs, saunas and in boats.
|#0616G Grit Top Cushion Tiles|
For maximum traction, use our grit top tile. The carbide grit provides maximum traction in areas where oil, water, solvents or chemicals are found. Same waffle grid design as our standard cushion tiles.
|#0617 CUSHION-LOK Mats|
Constructed of solid PVC vinyl. Highly resistant to industrial chemicals and provides fatigue relief. Raised diamond porthole system: facilitates drainage and improves traction. Bold O.S.H.A. colored ramps on 3 sides: easy non-trip access and instant identification. Reinforced wall pattern bottom surface provides fatigue relief while withstanding abusive loads. Modular design allows for custom-design to fit specific needs.
Available with Grip-Step® top coat: abrasive coating that provides additional traction (#0617G).
|#0617S CUSHION-LOK Solid Mats|
Solid version of our #0617 CUSHION-LOK mat.Highly resistant to industrial chemicals and provides fatigue relief. Bold O.S.H.A. Colored ramps on 3 sides, easy non-trip access and instant identification.
Reinforced wall pattern bottom surface provides fatigue relief while withstanding abusive loads. Modular design allows for custom-design to fit specific needs.
|#0618 3M Entrap Wet Area Matting|
Our resilient, vinyl, open-construction matting allows water to run through, so the matting stays drier. The special compound is resistant to chemicals commonly found in locker rooms, around saunas, whirlpools, showers and pool areas. The mat is uv stable and resists fungus and mildew. It is lightweight and can be easily cut to fit your application.
|#0620 Cushion Dek Matting|
Cushion-Dek™ is constructed of solid PVC, which is highly resistant to industrial chemicals. It also features slotted perforations that allow liquids to safely drain from the work surface. Raised pyramid top surface design improves traction. Slotted perforations (1/2" wide by 1 7/8" long)facilitates drainage.Studded bottom surface provides fatigue relief, facilitates drainage.Modular design allows for custom-design to fit specific needs.Also available with Grit Step abrasive coating for additional traction (#0620G).
|#0622 Safety Step Rubber Mats|
Low cost, high value mat for any industrial application. Modular design allows for custom installation. Beveled edges and corners are available.
Mats are available with holes for drainage or without holes for a solid application.
|#0623 Safe Walk Mats|
Raised hole perimeter offer greater cushioned support. Single wall construction prevents residue from collecting. No double-edged channels or sharp corners in which dirt and grease can collect. Residue washes thru the drain holes to the floor and thus is carried off. Our compound is more resistant to grease, oils and fats.
|#0624 Safe Walk Jr. Rubber Mats|
Finally, a mat with all the features that you need. Lightweight, comfortable and built-in beveled edges. Safe Walk Jr. Has holes for drainage. For use in machine shops, plants, factories or in the kitchen.
This mat is formulated with grease resistant properties for years of service.
|#0680 3M Clean Walk Mats|
Stop dirt in its tracks. The large adhesive surface has room to effectively capture contaminates. The mat is mounted on a 2 mil polyethylene backing for extra durability. Unique design has no beveled edge or frame to trap dirt. Mat can be applied to any clean, dry floor.
|#0690 Cushion Step Mat w/Rubber Marbleized Top|
Top quality, smooth rubber flooring permanently fused to a thick rubber base. Durable rubber offers greater traction than vinyl topping. Safety bevel edges available on standard and custom size mats. Here is a mat that gives the proper support without being mushy like utility mats.
|#0691 Cushion Step Mat with Vinyl Marbleized Top|
Easy clean vinyl top is permanently fused to our sponge rubber base.
The vinyl surface is resistant to oil, grease and all common acids when removed promptly. This material is more puncture resistant that rubber.
A safety bevel edge is available on standard and custom length mats.
|#0692 Industrial Deck Plate Anti-Fatigue Matting|
Durable, slip resistant surface has diamond pattern texture. Top surface is fused to pvc foam backing to eliminate de-lamination. Our material is resistant to most common fluids and chemicals and is available in two thicknesses. Safety bevel edging is available on both our standard size and custom size mats. Mat can also be ordered with bright colored borders for improved safety.
|#0693 Spark Safe Anti-Fatigue Matting|
This anti-fatigue mat consists of a specially formulated, rubber top surface laminated to a foam rubber base. The mat repels sparks and hot metal shards. This mat performs in tough, industrial environments, in both wet and dry applications. A textured top surface provides improved traction, added safety and long extended wear. The beveled edges on all sides offer added safety.
|#0694 Sta-Kleen Anti-Fatigue Matting|
This mat features a narrow-ribbed, vinyl surface cast to a pvc foam base offering cushioned comfort and durability for tough industrial environments. The rib design ensures quick and easy maintenance. The tough, vinyl rib surface provides added traction and improved safety.
Resists normal acids, oils, grease and most organic solvents, if removed promptly. A 1/8" extruded industrial grade solid vinyl surface fused to 3/8" closed cell vinyl sponge battles fatigue and creates a comfort zone.
|#0695 Stat Control Anti-Static Anti-Fatigue Matting|
This smooth surface anti-fatigue mat dissipates static electricity from workers to minimize damaging effects on sensitive electronic equipment. The durable vinyl top surface is cast to a resilient foam base promoting fatigue relief for improved worker productivity. A smooth surface design is easy to clean and provides superior traction. Edges are beveled for added safety. Excellent surface resistivity - surface to surface 107 ohms surface to ground 107 ohms. For maximum effectiveness use an optional grounding cord every 10'. Standard size mats come with one grounding cord.
|#0696 Workers Delight Rubber Top Anti-Fatigue Matting|
Our high-performance Workers-Delight™ matting features patent pending Zedlan™ foam fused to our marbelized rubber surface. Zedlan™ foam provides a softer, more resilient foam base than vinyl foam. Provides improved resiliency in cold environments and a resistance to most common fluids and chemicals. Our exclusive fusion technology eliminates the chance of delamination occurring between the top and bottom surfaces. Mats are available with beveled edging on all four sides reduces trip hazards.
|#0697 Workers-Delight™ Diamond Design Anti-Fatigue Matting|
Our high-performance Workers-Delight™ matting features patent pending Zedlan™ foam fused to our diamond design vinyl surface.
Zedlan™ foam provides a softer, more resilient foam base than vinyl foam. Provides improved resiliency in cold environments and a resistance to most common fluids and chemicals. Our exclusive fusion technology eliminates the chance of delamination occurring between the top and bottom surfaces. Mats are available with beveled edging on all four sides reduces trip.
|#0900 Punishment Pads|
These multi-purpose pads can take all the punishment you can throw at them. Use them in weight rooms, at workout stations, even in horse trailers or stalls. Protects your floor and provides sure footing.
|#0904 Classic Impression Logo Mats|
Our most versatile logo mat yet. Style and quality are combined to create attractive designs that are printed onto the face of the mat with state of the art digital printer. The Classic Impressions manufacturing process can produce the most detailed designs that include small letters and fine details from a color palette of 24 beautiful colors. "Phase-in" colors that produce a shaded effect are possible. All classic impressions logo mats are manufactured with a premium static dissipative 100% nylon yarn that is dyed using perma-dye plus stain stopper.
Each mat is backed with a solid rubber backing for the ultimate in durability.
|#0905 Graphic Inlay Logo Mats|
Each element of a Graphic Inlay® logo mat is precisely cut from durable nylon fabric and hand-assembled to enhance any corporate logo or symbol. Project business images with striking clarity of design and luxurious texture. Graphic Inlay® mats are the perfect welcome at entrances and in lobbies. Graphic Inlay® mats protect carpet, tile, and waxed floor finishes as they trap the dirt, moisture and grit that increase daily maintenance costs. The skid-resistant nitrile rubber backing holds the mat securely and is resistant to oil and grease.
|#0910 Graphic Tuft Logo Mats|
Graphic Tuft® logo mats combines the ancient art of tapestry with precise modern technology to reproduce beautiful designs onto durable washable mats. Mats feature 100% solution-dyed nylon for years of colorfast wear. The skid-resistant nitrile rubber backing resists oil and grease. Create the largest logo mats in the industry! Full-size designs and logos are available in mats up to 12' x 16'. Choose up to six colors per design from our 32-color array.
|#0920 Water Hog Inlay Logo Mats|
Put your company logo or any message on the industry's finest indoor/outdoor mat. With our unique inlay process, the logo or message is specially cut out of different carpet colors. These carpet sections are then pieced together and bonded to a rubber backing to create a beautiful, long -lasting and practical image mat for any workplace.
Select from 18 attractive colors in a large variety of sizes ranging from 2'x3' to 6'x20'. Available in flat or gripper backing, and available with Water Hog Classic™ rubber border or Water Hog™ Fashion Fabric border.
|#0950 Super Scrape Impression Logo Mats|
Effectively scrapes tough dirt and grime off feet. Durable nitrile-rubber mat provides slip-resistant surface. Super Scrape Logos are ideal for kitchens, locker rooms, slippery inclines, restaurants, production areas and outside entrances. Super Scrape Logos are available in red, green, yellow, orange, gold, white, and blue.
|#0990 Message / Slogan Mats|
These bright bold mats are a perfect way to capture the attention of your employees and visitors. The applications are endless and they cut down on maintenance costs. Choose from these standard designs or create your own message. Available in gripper, flat, or suction type of backing.
|#1000 Strip Doors|
Strip doors provide see through barriers that allow quick and easy passage of personnel, products, and equipment. They can be manufactured to accommodate any size door opening. Strip doors are effective in conserving energy and provide a barrier for dust control.
|#1060 Commercial Neoprene Sheet Rubber|
Our commercial blend, neoprene compound is adaptable to extreme weather conditions since it resists rotting, checking and cracking due to ozone exposure. Neoprene sheet rubber provides good resistance to oil and gasoline in gasket and flange applications.
|#2075 Red SBR Sheet Rubber|
An economical, non oil resistant compound that resists flow under compression. Offers moderate to good performance against low pressure. Also has good aging, abrasion and tear resistance. Easily conforms to uneven flange surfaces. Recommended for low pressure applications such as washers and gaskets for the heating and plumbing trades.
Slip resistant backing to help prevent a mat from moving on hard surfaces. Available on most carpet top mats.
Anti-slip backing designed for mats used on top of cut pile carpeting. Available on most carpet top mats.
|Blower Power Packs|
The Tornado Blowers are built tornado tough with a cast aluminum housing. The units feature a specially designed flexible rubber nozzle which allows air to be directed to hard to reach areas. A 50 foot safety cord is provided with the machine. Choose the Tornado Blowers for many years of service and reliability.
|CFV 125 Critical Filter Vacuum|
The CFV 125 was conceived and designed to handle the critical dry recovery operations where other units simply should not be used.
Safety, controlled recovery and disposal are all combined in a compact, heavy gauge steel housing a powerful 4-stage HEPA Filter system and 75 c.f.m. Of dry pick-up power. Features include a 7.4-gallon stainless steel tank, lift-grip handle, and a four-caster, bumper-guarded carrier.
The unique four stage filtration system is accomplished by using a paper filter collection bag, additonal primary paper filter, dacron filter, and main HEPA Filter. Supplement this system with optional plastic liner disposal bag. Add attachment set number 90656 to complete the unit.
|Jumbo Air Series of Wet/Dry Vacuums|
These compressed air powered models, use either a single, dual or quad head configuration to create significant waterlift or suction power far superior to traditonal wet/dry vacuums. These units have no moving parts and therefore are spark free. This jumbo series uses a unique external filtering system that allows for true simultaneous wet/dry recovery. This is the perfect solution for manufacturing, distribution and other industrial facilties where air power is provided. All units come complete with a specially built 55 gallon rolled top drum and industrial steel cart.
|Jumbo Electric Series of Wet/Dry Vacuums|
It is a simple principle; the higher the C.F.M. a vacuum generates, the better suited it is for recovering dry debris and bulk material.
Electric Jumbo Vacuum Systems are appropriate for use in recovering heavy solid debris such as metal shavings and chips, sawdust, powders (fine and ultra fine), sand and oil dry . The units are also effective in recovering water, machine oils and cutting oils. These Jumbo's have been designed specifically for industrial applications and feature heavy duty steel vacuum covers, aluminum housing blower powerpack(s) and a rolled-top steel 55-gallon drum. External poly filter bags allow for maximum filtering area and separation of the debris from the filtering system. Add 90637 (single) and 90633 (dual) attachment sets to complete the package. Neoprene hoses also available to tackle the nastiest oil recovery jobs.
|Jumbo Internal Wet Only Air Vacuums|
Powered by compressed air, Tornado's internal filtered Wet Jumbo Air Vacuum creates exceptional waterlift substantially beyond your typical vacuum. These machines have been developed specifically to cover industrial rapid high-volume recovery environments. Our Air Jumbo's work exceedingly well handling the following maintenance challenges: heavy oil, machine oil, printer's and other inks, sludge and most all other industrial wet pick up problems. Patented venturi powerheads are fitted on a rolled top 55 gallon drum all of which sits on a heavy duty four wheel steel dolly for easy transport. Order in either dual head or quad head configurations. Specific air line and air compressor hp requirements apply as detailed on our product brochure.
|Kaimotion II Ergo Mopping System|
The Kaimotion II equips the custodian for any cleaning challenge around the building. Clean walls, floors, chalkboards, desktops or any other hard surface. The kaimotion ii system is also designed for flawless floor waxing and finishing, saving on costly and time-consuming redos. The 16 gallon solution tank and a stack of cleaning pads will clean all the hallways in a typical school building in one trip. Kaimotion II is also equipped with a 48" pad holder to clean larger areas faster.
|Kaimotion Self Dispensing Solution Tank|
Precise flow control spigot throttle and gauge fingers to properly manage the amount of solution used for floor cleaning and waxing.
Saving on chemical costs and producing better results. Cleaning solution stays fresh because the dirt never enter the solution tank. Washable, microfiber pads are changed as you clean, ensuring effective soil removal and eliminating cross-contamination. Plus, fewer trips to the janitors closet saves time and energy.
|Kaimotion SUV Janitor\'s Closet on Wheels|
The Kaimotion SUV equips the custodian for any cleaning challenge around the building. Clean walls, floors, chalkboards, desktops or any other hard surface. The Kaimotion SUV system is also designed for flawless floor waxing and finishing, saving on costly and time-consuming redos. The 16 gallon solution tank and a stack of cleaning pads will clean all the hallways in a typical school building in one trip. Includes the Kaizoom a feather-light, telescopic handled mop that uses the microfiber pads to easily micro-clean walls and overhead surfaces. The removable storage compartment carries extra tools or supplies and makes loading and storage more convenient. A side-mounted tool organizer keeps tools handy. Conveniently transport upright or backpack vacuum cleaners.
Combined citrus d-limonene with hydrogen peroxide to make an environmentally friendly, multipurpose. Ph neutral cleaner that is completely safe for personnel and building surfaces.
Blows away all other restroom cleaners. Kaiblooey is low foaming and contains a blend of fast acting mild acids to de-scale mineral deposits and remove soap scum.
A heavy duty degreaser that rapidly penetrates oils, grease fats, and soils.
Helps water sheet off hard surfaces to wipe out hard water spots before they get started. It also reduces the size of the water droplets, speeding up the drying process.
A hospital grade broad spectrum disinfectant that can be used in restrooms and hallways. With a neutral ph, it will not attack the floor finish.
Mild acid, EPA registered, broad-spectrum disinfectant designed for cleaning restrooms and shower rooms.
|Kaivac Comparison Chart|
|Kaivac No-Touch Restroom Cleaning Machine|
Cleans soil and germs that conventional cleaning leaves behind.
Removes odor-causing bacteria, leaving buildings and restrooms smelling fresher. An indoor pressure washer combined with chemical injection allows workers to clean without ever having to touch contaminated surfaces. Simply spray cleaning solution on fixtures and surfaces. Then blast soils to the floor with the high-pressure water spray. To finish up, vacuum the floor dry completely removing all soil and bacteria.
|Kaizen No Touch Restroom Cleaning Machine|
Cleans soil and germs that conventional cleaning leaves behind.
Removes odor-causing bacteria, leaving buildings and restrooms smelling fresher. An indoor pressure washer combined with chemical injection allows workers to clean without ever having to touch contaminated surfaces. Simply spray cleaning solution on fixtures and surfaces, then blast soils to the floor with the high-pressure water spray.
To finish up, vacuum the floor dry completely removing all soil and bacteria.